par chybicek pri bootu (?)

pri bootu mi fidorka haze par nehezkych zprav…
tesne pred spustenim plymouthu a inicializace se zjevi zprava


handling fault status reg 3
[DMA Write] Request device [00:02.0] fault address ...
[Fault reason 05] PTE Write access not set

a dale pri inicializaci (hned na zacatek)


Starting udev: udevd-work[397]: error opening ATTR{/sys/devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.0/power/level} for writing: No such file or directory

… a jeste bych mel zvidavou otazku - pri vypisu stavu inicializace (sluzba, [OK]) lze nejak zvetsit mezeru?


ip6tables: Loading additional modules: nf_conntrack_netbios[  OK  ]onntrack_ftp 
iptables: Applying firewall rules:                         [  OK  ]
iptables: Loading additional modules: nf_conntrack_netbios_[  OK  ]nntrack_ftp 

aby nedochazelo k rozdeleni zpravy?

PS: vyrobil sem par videi plymouth temat, v jednom z nich sou videt i tyto chybove hlasky: http://www.youtube.com/watch?v=yIrzAmY4bSU
PS2: Lenovo ThinkPad R400 :wink:

ad OK … v /etc/sysconfig/init poedituj polozku RES_COL=60 …zvysit na pozadovany sloupec.

ostatni chyby jsou asi hardware specific … mohlo by pomoci nejake nastaveni BIOS nebo kernel parametr … je potreba zagooglit, ale asi to nebude nic tragickeho, pokud stroj funguje.

Kalidah: diky za “[OK]” :slight_smile:

ja sem prave zkousel googlit a nic kloudneho jsem nenasel. vse funguje jak ma :slight_smile: to ano… ale treba v F10 a F11 se mi nic takoveho pri bootu nezjevovalo. v podstate :smiley: mi jde jen o tu “estetiku” :wink: (a navic to nevypada dobre, kdyz chci vytrit windozakum zrak a pri bootu to haze errory)

To co se ti vypisuje je bohuzel jen cast hlasek, zrejme na error vystup - podivej se do vypisu dmesg a zkus kouknout co je okolo za “bezne” hlaseni.

Co se tyce udev, tak tam bych zkusil projit pravidla v /etc/udev/rules.d/. Jen tak od boku bych rekl ze to muze byt neco z 60-fprint-autosuspend.rules - bude to nejake usb zarizeni ktere nema powermanagement nebo tak neco. Koukni do lsusb co je to za HW a hledej dal timto smerem.

tak sem si vypsal dmesg, ale teda vazne v tom nic nevidim. moc moudrej z toho nejsem


Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.31.12-174.2.3.fc12.x86_64 (mockbuild@x86-05.phx2.fedoraproject.org) (gcc version 4.4.2 20091222 (Red Hat 4.4.2-20) (GCC) ) #1 SMP Mon Jan 18 19:52:07 UTC 2010
Command line: ro root=/dev/sda7  LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us rhgb quiet
KERNEL supported cpus:
  Intel GenuineIntel
  AMD AuthenticAMD
  Centaur CentaurHauls
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009ac00 (usable)
 BIOS-e820: 000000000009ac00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000d6000 - 00000000000d8000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 00000000bd4a1000 (usable)
 BIOS-e820: 00000000bd4a1000 - 00000000bd4a7000 (reserved)
 BIOS-e820: 00000000bd4a7000 - 00000000bd5b7000 (usable)
 BIOS-e820: 00000000bd5b7000 - 00000000bd60f000 (reserved)
 BIOS-e820: 00000000bd60f000 - 00000000bd6c6000 (usable)
 BIOS-e820: 00000000bd6c6000 - 00000000bd6d1000 (ACPI NVS)
 BIOS-e820: 00000000bd6d1000 - 00000000bd6d4000 (ACPI data)
 BIOS-e820: 00000000bd6d4000 - 00000000bd6d8000 (reserved)
 BIOS-e820: 00000000bd6d8000 - 00000000bd6dc000 (ACPI NVS)
 BIOS-e820: 00000000bd6dc000 - 00000000bd6df000 (reserved)
 BIOS-e820: 00000000bd6df000 - 00000000bd706000 (ACPI NVS)
 BIOS-e820: 00000000bd706000 - 00000000bd708000 (ACPI data)
 BIOS-e820: 00000000bd708000 - 00000000bd90f000 (reserved)
 BIOS-e820: 00000000bd90f000 - 00000000bd99f000 (ACPI NVS)
 BIOS-e820: 00000000bd99f000 - 00000000bd9ff000 (ACPI data)
 BIOS-e820: 00000000bd9ff000 - 00000000bda00000 (usable)
 BIOS-e820: 00000000bdc00000 - 00000000c0000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
 BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
 BIOS-e820: 00000000fed10000 - 00000000fed14000 (reserved)
 BIOS-e820: 00000000fed18000 - 00000000fed1a000 (reserved)
 BIOS-e820: 00000000fed1c000 - 00000000fed90000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ff800000 - 0000000100000000 (reserved)
 BIOS-e820: 0000000100000000 - 000000013c000000 (usable)
DMI present.
last_pfn = 0x13c000 max_arch_pfn = 0x400000000
MTRR default type: uncachable
MTRR fixed ranges enabled:
  00000-9FFFF write-back
  A0000-BFFFF uncachable
  C0000-D7FFF write-protect
  D8000-DBFFF uncachable
  DC000-FFFFF write-protect
MTRR variable ranges enabled:
  0 base 13C000000 mask FFC000000 uncachable
  1 base 0BE000000 mask FFE000000 uncachable
  2 base 000000000 mask F80000000 write-back
  3 base 080000000 mask FC0000000 write-back
  4 base 100000000 mask FC0000000 write-back
  5 base 0BDC00000 mask FFFC00000 uncachable
  6 disabled
  7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
original variable MTRRs
reg 0, base: 5056MB, range: 64MB, type UC
reg 1, base: 3040MB, range: 32MB, type UC
reg 2, base: 0GB, range: 2GB, type WB
reg 3, base: 2GB, range: 1GB, type WB
reg 4, base: 4GB, range: 1GB, type WB
reg 5, base: 3036MB, range: 4MB, type UC
total RAM coverred: 3996M
Found optimal setting for mtrr clean up
 gran_size: 64K 	chunk_size: 128M 	num_reg: 6  	lose cover RAM: 0G
New variable MTRRs
reg 0, base: 0GB, range: 2GB, type WB
reg 1, base: 2GB, range: 1GB, type WB
reg 2, base: 3036MB, range: 4MB, type UC
reg 3, base: 3040MB, range: 32MB, type UC
reg 4, base: 4GB, range: 1GB, type WB
reg 5, base: 5056MB, range: 64MB, type UC
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
e820 update range: 00000000bdc00000 - 0000000100000000 (usable) ==> (reserved)
last_pfn = 0xbda00 max_arch_pfn = 0x400000000
initial memory mapped : 0 - 20000000
init_memory_mapping: 0000000000000000-00000000bda00000
 0000000000 - 00bda00000 page 2M
kernel direct mapping tables up to bda00000 @ 8000-c000
init_memory_mapping: 0000000100000000-000000013c000000
 0100000000 - 013c000000 page 2M
kernel direct mapping tables up to 13c000000 @ a000-10000
RAMDISK: 373f9000 - 37fefa87
ACPI: RSDP 00000000000f6450 00024 (v02 LENOVO)
ACPI: XSDT 00000000bd94a1df 0009C (v01 LENOVO TP-7U    00003010  LTP 00000000)
ACPI: FACP 00000000bd94a300 000F4 (v03 LENOVO TP-7U    00003010 LNVO 00000001)
ACPI: DSDT 00000000bd94a6db 0F48F (v01 LENOVO TP-7U    00003010 MSFT 03000000)
ACPI: FACS 00000000bd98e000 00040
ACPI: SSDT 00000000bd94a4b4 00227 (v01 LENOVO TP-7U    00003010 MSFT 03000000)
ACPI: ECDT 00000000bd959b6a 00052 (v01 LENOVO TP-7U    00003010 LNVO 00000001)
ACPI: APIC 00000000bd959bbc 00078 (v01 LENOVO TP-7U    00003010 LNVO 00000001)
ACPI: MCFG 00000000bd959c34 0003C (v01 LENOVO TP-7U    00003010 LNVO 00000001)
ACPI: HPET 00000000bd959c70 00038 (v01 LENOVO TP-7U    00003010 LNVO 00000001)
ACPI: SLIC 00000000bd959dc2 00176 (v01 LENOVO TP-7U    00003010  LTP 00000000)
ACPI: BOOT 00000000bd959f38 00028 (v01 LENOVO TP-7U    00003010  LTP 00000001)
ACPI: ASF! 00000000bd959f60 000A0 (v16 LENOVO TP-7U    00003010 PTL  00000001)
ACPI: SSDT 00000000bd98d213 0054F (v01 LENOVO TP-7U    00003010 INTL 20050513)
ACPI: TCPA 00000000bd707000 00032 (v00                 00000000      00000000)
ACPI: DMAR 00000000bd706000 00120 (v01                00000001      00000000)
ACPI: SSDT 00000000bd6d3000 00655 (v01  PmRef    CpuPm 00003000 INTL 20050624)
ACPI: SSDT 00000000bd6d2000 00274 (v01  PmRef  Cpu0Tst 00003000 INTL 20050624)
ACPI: SSDT 00000000bd6d1000 00242 (v01  PmRef    ApTst 00003000 INTL 20050624)
ACPI: Local APIC address 0xfee00000
No NUMA configuration found
Faking a node at 0000000000000000-000000013c000000
Bootmem setup node 0 0000000000000000-000000013c000000
  NODE_DATA [000000000000b000 - 0000000000020fff]
  bootmap [0000000000021000 -  00000000000487ff] pages 28
(8 early reservations) ==> bootmem [0000000000 - 013c000000]
  #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
  #1 [0000006000 - 0000008000]       TRAMPOLINE ==> [0000006000 - 0000008000]
  #2 [0001000000 - 00019b0b40]    TEXT DATA BSS ==> [0001000000 - 00019b0b40]
  #3 [00373f9000 - 0037fefa87]          RAMDISK ==> [00373f9000 - 0037fefa87]
  #4 [000009ac00 - 0000100000]    BIOS reserved ==> [000009ac00 - 0000100000]
  #5 [00019b1000 - 00019b114c]              BRK ==> [00019b1000 - 00019b114c]
  #6 [0000008000 - 000000a000]          PGTABLE ==> [0000008000 - 000000a000]
  #7 [000000a000 - 000000b000]          PGTABLE ==> [000000a000 - 000000b000]
found SMP MP-table at [ffff8800000f6490] f6490
 [ffffea0000000000-ffffea00045fffff] PMD -> [ffff880028600000-ffff88002bdfffff] on node 0
Zone PFN ranges:
  DMA      0x00000000 -> 0x00001000
  DMA32    0x00001000 -> 0x00100000
  Normal   0x00100000 -> 0x0013c000
Movable zone start PFN for each node
early_node_map[6] active PFN ranges
    0: 0x00000000 -> 0x0000009a
    0: 0x00000100 -> 0x000bd4a1
    0: 0x000bd4a7 -> 0x000bd5b7
    0: 0x000bd60f -> 0x000bd6c6
    0: 0x000bd9ff -> 0x000bda00
    0: 0x00100000 -> 0x0013c000
On node 0 totalpages: 1021443
  DMA zone: 56 pages used for memmap
  DMA zone: 107 pages reserved
  DMA zone: 3831 pages, LIFO batch:0
  DMA32 zone: 14280 pages used for memmap
  DMA32 zone: 757409 pages, LIFO batch:31
  Normal zone: 3360 pages used for memmap
  Normal zone: 242400 pages, LIFO batch:31
ACPI: PM-Timer IO Port: 0x1008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] disabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] disabled)
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a201 base: 0xfed00000
SMP: Allowing 4 CPUs, 2 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009a000 - 000000000009b000
PM: Registered nosave memory: 000000000009b000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000d6000
PM: Registered nosave memory: 00000000000d6000 - 00000000000d8000
PM: Registered nosave memory: 00000000000d8000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
PM: Registered nosave memory: 00000000bd4a1000 - 00000000bd4a7000
PM: Registered nosave memory: 00000000bd5b7000 - 00000000bd60f000
PM: Registered nosave memory: 00000000bd6c6000 - 00000000bd6d1000
PM: Registered nosave memory: 00000000bd6d1000 - 00000000bd6d4000
PM: Registered nosave memory: 00000000bd6d4000 - 00000000bd6d8000
PM: Registered nosave memory: 00000000bd6d8000 - 00000000bd6dc000
PM: Registered nosave memory: 00000000bd6dc000 - 00000000bd6df000
PM: Registered nosave memory: 00000000bd6df000 - 00000000bd706000
PM: Registered nosave memory: 00000000bd706000 - 00000000bd708000
PM: Registered nosave memory: 00000000bd708000 - 00000000bd90f000
PM: Registered nosave memory: 00000000bd90f000 - 00000000bd99f000
PM: Registered nosave memory: 00000000bd99f000 - 00000000bd9ff000
PM: Registered nosave memory: 00000000bda00000 - 00000000bdc00000
PM: Registered nosave memory: 00000000bdc00000 - 00000000c0000000
PM: Registered nosave memory: 00000000c0000000 - 00000000e0000000
PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
PM: Registered nosave memory: 00000000f0000000 - 00000000fec00000
PM: Registered nosave memory: 00000000fec00000 - 00000000fec10000
PM: Registered nosave memory: 00000000fec10000 - 00000000fed00000
PM: Registered nosave memory: 00000000fed00000 - 00000000fed10000
PM: Registered nosave memory: 00000000fed10000 - 00000000fed14000
PM: Registered nosave memory: 00000000fed14000 - 00000000fed18000
PM: Registered nosave memory: 00000000fed18000 - 00000000fed1a000
PM: Registered nosave memory: 00000000fed1a000 - 00000000fed1c000
PM: Registered nosave memory: 00000000fed1c000 - 00000000fed90000
PM: Registered nosave memory: 00000000fed90000 - 00000000fee00000
PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
PM: Registered nosave memory: 00000000fee01000 - 00000000ff800000
PM: Registered nosave memory: 00000000ff800000 - 0000000100000000
Allocating PCI resources starting at c0000000 (gap: c0000000:20000000)
NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:4 nr_node_ids:1
PERCPU: Embedded 29 pages at ffff880028023000, static data 90080 bytes
Built 1 zonelists in Node order, mobility grouping on.  Total pages: 1003640
Policy zone: Normal
Kernel command line: ro root=/dev/sda7  LANG=en_US.UTF-8 SYSFONT=latarcyrheb-sun16 KEYBOARDTYPE=pc KEYTABLE=us rhgb quiet
PID hash table entries: 4096 (order: 12, 32768 bytes)
Initializing CPU#0
Checking aperture...
No AGP bridge found
Calgary: detecting Calgary via BIOS EBDA area
Calgary: Unable to locate Rio Grande table in EBDA - bailing!
Memory: 4005468k/5177344k available (4238k kernel code, 1091572k absent, 80304k reserved, 2924k data, 1328k init)
SLUB: Genslabs=14, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:4352 nr_irqs:440
Extended CMOS year: 2000
Fast TSC calibration using PIT
Detected 1795.342 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
allocated 41943040 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
hpet clockevent registered
HPET: 4 timers in total, 0 timers will be used for per-cpu timer
Calibrating delay loop (skipped), value calculated using timer frequency.. 3590.68 BogoMIPS (lpj=1795342)
Security Framework initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Mount-cache hash table entries: 256
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU 0/0x0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 6 MCE banks
CPU0: Thermal monitoring enabled (TM2)
using mwait in idle threads.
Performance Counters: Core2 events, Intel PMU driver.
... version:                 2
... bit width:               40
... generic counters:        2
... value mask:              000000ffffffffff
... max period:              000000007fffffff
... fixed-purpose counters:  3
... counter mask:            0000000700000003
ACPI: Core revision 20090521
ftrace: converting mcount calls to 0f 1f 44 00 00
ftrace: allocating 20894 entries in 82 pages
DMAR:Host address width 36
DMAR:DRHD base: 0x000000feb03000 flags: 0x0
IOMMU feb03000: ver 1:0 cap c9008020e30260 ecap 1000
DMAR:DRHD base: 0x000000feb01000 flags: 0x0
IOMMU feb01000: ver 1:0 cap c0000020630260 ecap 1000
DMAR:DRHD base: 0x000000feb00000 flags: 0x0
IOMMU feb00000: ver 1:0 cap c0000020630270 ecap 1000
DMAR:DRHD base: 0x000000feb02000 flags: 0x1
IOMMU feb02000: ver 1:0 cap c9008020630260 ecap 1000
DMAR:RMRR base: 0x000000fc326c00 end: 0x000000fc3273ff
DMAR:RMRR base: 0x000000bdc00000 end: 0x000000bfffffff
DMAR:No ATSR found
Setting APIC routing to flat
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Core(TM)2 Duo CPU     T5670  @ 1.80GHz stepping 0d
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3590.83 BogoMIPS (lpj=1795416)
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 2048K
CPU 1/0x1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
mce: CPU supports 6 MCE banks
CPU1: Thermal monitoring enabled (TM2)
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Core(TM)2 Duo CPU     T5670  @ 1.80GHz stepping 0d
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (7181.51 BogoMIPS).
sizeof(vma)=176 bytes
sizeof(page)=56 bytes
sizeof(inode)=584 bytes
sizeof(dentry)=192 bytes
sizeof(ext3inode)=776 bytes
sizeof(buffer_head)=104 bytes
sizeof(skbuff)=248 bytes
sizeof(task_struct)=6008 bytes
CPU0 attaching sched-domain:
 domain 0: span 0-1 level MC
  groups: 0 1
CPU1 attaching sched-domain:
 domain 0: span 0-1 level MC
  groups: 1 0
Booting paravirtualized kernel on bare hardware
regulator: core version 0.5
Time: 11:48:36  Date: 02/02/10
NET: Registered protocol family 16
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
PCI: MCFG configuration 0: base e0000000 segment 0 buses 0 - 63
PCI: MCFG area at e0000000 reserved in E820
PCI: Using MMCONFIG at e0000000 - e3ffffff
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: EC description table is found, configuring boot EC
ACPI: BIOS _OSI(Linux) query ignored
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x11, I/O: command/status = 0x66, data = 0x62
ACPI: Power Resource [PUBS] (on)
ACPI: ACPI Dock Station Driver: 3 docks/bays found
ACPI: PCI Root Bridge [PCI0] (0000:00)
DMAR: Forcing write-buffer flush capability
pci 0000:00:02.0: reg 10 64bit mmio: [0xf4400000-0xf47fffff]
pci 0000:00:02.0: reg 18 64bit mmio: [0xd0000000-0xdfffffff]
pci 0000:00:02.0: reg 20 io port: [0x1800-0x1807]
pci 0000:00:02.1: reg 10 64bit mmio: [0xf4200000-0xf42fffff]
pci 0000:00:03.0: reg 10 64bit mmio: [0xfc326800-0xfc32680f]
pci 0000:00:03.0: PME# supported from D0 D3hot D3cold
pci 0000:00:03.0: PME# disabled
pci 0000:00:19.0: reg 10 32bit mmio: [0xfc100000-0xfc11ffff]
pci 0000:00:19.0: reg 14 32bit mmio: [0xfc325000-0xfc325fff]
pci 0000:00:19.0: reg 18 io port: [0x1840-0x185f]
pci 0000:00:19.0: PME# supported from D0 D3hot D3cold
pci 0000:00:19.0: PME# disabled
pci 0000:00:1a.0: reg 20 io port: [0x1860-0x187f]
pci 0000:00:1a.1: reg 20 io port: [0x1880-0x189f]
pci 0000:00:1a.2: reg 20 io port: [0x18a0-0x18bf]
pci 0000:00:1a.7: reg 10 32bit mmio: [0xfc326c00-0xfc326fff]
pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1a.7: PME# disabled
pci 0000:00:1b.0: reg 10 64bit mmio: [0xfc320000-0xfc323fff]
pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1b.0: PME# disabled
pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.0: PME# disabled
pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.1: PME# disabled
pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.2: PME# disabled
pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.3: PME# disabled
pci 0000:00:1c.4: PME# supported from D0 D3hot D3cold
pci 0000:00:1c.4: PME# disabled
pci 0000:00:1d.0: reg 20 io port: [0x18c0-0x18df]
pci 0000:00:1d.1: reg 20 io port: [0x18e0-0x18ff]
pci 0000:00:1d.2: reg 20 io port: [0x1c00-0x1c1f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xfc327000-0xfc3273ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.2: reg 10 io port: [0x1c48-0x1c4f]
pci 0000:00:1f.2: reg 14 io port: [0x183c-0x183f]
pci 0000:00:1f.2: reg 18 io port: [0x1c40-0x1c47]
pci 0000:00:1f.2: reg 1c io port: [0x1838-0x183b]
pci 0000:00:1f.2: reg 20 io port: [0x1c20-0x1c3f]
pci 0000:00:1f.2: reg 24 32bit mmio: [0xfc326000-0xfc3267ff]
pci 0000:00:1f.2: PME# supported from D3hot
pci 0000:00:1f.2: PME# disabled
pci 0000:00:1f.3: reg 10 64bit mmio: [0xfc327400-0xfc3274ff]
pci 0000:00:1f.3: reg 20 io port: [0x1c60-0x1c7f]
pci 0000:03:00.0: reg 10 64bit mmio: [0xf4300000-0xf4301fff]
pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
pci 0000:03:00.0: PME# disabled
pci 0000:00:1c.1: bridge 32bit mmio: [0xf4300000-0xf43fffff]
pci 0000:04:00.0: reg 10 32bit mmio: [0xfc000000-0xfc0003ff]
pci 0000:04:00.0: reg 18 io port: [0x2000-0x20ff]
pci 0000:04:00.0: reg 30 32bit mmio: [0x000000-0x00ffff]
pci 0000:00:1c.2: bridge io port: [0x2000-0x2fff]
pci 0000:00:1c.2: bridge 32bit mmio: [0xfc000000-0xfc0fffff]
pci 0000:00:1c.3: bridge io port: [0x3000-0x3fff]
pci 0000:00:1c.3: bridge 32bit mmio: [0xf8000000-0xf9ffffff]
pci 0000:00:1c.3: bridge 64bit mmio pref: [0xf4000000-0xf40fffff]
pci 0000:00:1c.4: bridge io port: [0x4000-0x4fff]
pci 0000:00:1c.4: bridge 32bit mmio: [0xfa000000-0xfbffffff]
pci 0000:00:1c.4: bridge 64bit mmio pref: [0xf4100000-0xf41fffff]
pci 0000:15:00.0: reg 10 32bit mmio: [0xf4800000-0xf4800fff]
pci 0000:15:00.0: supports D1 D2
pci 0000:15:00.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:15:00.0: PME# disabled
pci 0000:15:00.1: reg 10 32bit mmio: [0xf4801000-0xf48017ff]
pci 0000:15:00.1: supports D1 D2
pci 0000:15:00.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:15:00.1: PME# disabled
pci 0000:15:00.2: reg 10 32bit mmio: [0xf4801800-0xf48018ff]
pci 0000:15:00.2: supports D1 D2
pci 0000:15:00.2: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:15:00.2: PME# disabled
pci 0000:15:00.3: reg 10 32bit mmio: [0xf4801c00-0xf4801cff]
pci 0000:15:00.3: supports D1 D2
pci 0000:15:00.3: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:15:00.3: PME# disabled
pci 0000:15:00.4: reg 10 32bit mmio: [0xf4802000-0xf48020ff]
pci 0000:15:00.4: supports D1 D2
pci 0000:15:00.4: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:15:00.4: PME# disabled
pci 0000:15:00.5: reg 10 32bit mmio: [0xf4802400-0xf48024ff]
pci 0000:15:00.5: supports D1 D2
pci 0000:15:00.5: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:15:00.5: PME# disabled
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge io port: [0x5000-0x8fff]
pci 0000:00:1e.0: bridge 32bit mmio: [0xf4800000-0xf7ffffff]
pci 0000:00:1e.0: bridge 64bit mmio pref: [0xf0000000-0xf3ffffff]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11)
vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: old code would have set cacheline size to 32 bytes, but clflush_size = 64
PCI: pci_cache_line_size set to 64 bytes
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
DMAR:Device scope device [0000:00:03.02] not found
DMAR:Device scope device [0000:00:03.02] not found
DMAR:Device scope device [0000:00:03.03] not found
DMAR:Device scope device [0000:00:03.03] not found
IOMMU 0xfeb00000: using Register based invalidation
IOMMU 0xfeb01000: using Register based invalidation
IOMMU 0xfeb03000: using Register based invalidation
IOMMU 0xfeb02000: using Register based invalidation
IOMMU: software identity mapping for device 0000:00:02.0
IOMMU: software identity mapping for device 0000:00:02.1
IOMMU: Setting RMRR:
IOMMU: Setting identity map for device 0000:00:02.0 [0xbdc00000 - 0xc0000000]
IOMMU: Setting identity map for device 0000:00:02.1 [0xbdc00000 - 0xc0000000]
IOMMU: Setting identity map for device 0000:00:1d.0 [0xfc326c00 - 0xfc327400]
IOMMU: Setting identity map for device 0000:00:1d.1 [0xfc326c00 - 0xfc327400]
IOMMU: Setting identity map for device 0000:00:1d.2 [0xfc326c00 - 0xfc327400]
IOMMU: Setting identity map for device 0000:00:1d.7 [0xfc326c00 - 0xfc327400]
IOMMU: Setting identity map for device 0000:00:1a.0 [0xfc326c00 - 0xfc327400]
IOMMU: Setting identity map for device 0000:00:1a.1 [0xfc326c00 - 0xfc327400]
IOMMU: Setting identity map for device 0000:00:1a.2 [0xfc326c00 - 0xfc327400]
IOMMU: Setting identity map for device 0000:00:1a.7 [0xfc326c00 - 0xfc327400]
IOMMU: Prepare 0-16MiB unity mapping for LPC
IOMMU: Setting identity map for device 0000:00:1f.0 [0x0 - 0x1000000]
  alloc irq_desc for 24 on node 0
  alloc kstat_irqs on node 0
  alloc irq_desc for 25 on node 0
  alloc kstat_irqs on node 0
DRHD: handling fault status reg 3
  alloc irq_desc for 26 on node 0
DMAR:[DMA Write] Request device [00:02.0] fault addr ffffff000 
DMAR:[fault reason 05] PTE Write access is not set
  alloc kstat_irqs on node 0
  alloc irq_desc for 27 on node 0
  alloc kstat_irqs on node 0
PCI-DMA: Intel(R) Virtualization Technology for Directed I/O
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0
hpet0: 4 comparators, 64-bit 14.318180 MHz counter
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
system 00:00: iomem range 0x0-0x9ffff could not be reserved
system 00:00: iomem range 0xc0000-0xc3fff has been reserved
system 00:00: iomem range 0xc4000-0xc7fff has been reserved
system 00:00: iomem range 0xc8000-0xcbfff has been reserved
system 00:00: iomem range 0xcc000-0xcffff has been reserved
system 00:00: iomem range 0xd0000-0xd3fff has been reserved
system 00:00: iomem range 0xd4000-0xd7fff could not be reserved
system 00:00: iomem range 0xe0000-0xe3fff could not be reserved
system 00:00: iomem range 0xe4000-0xe7fff could not be reserved
system 00:00: iomem range 0xe8000-0xebfff could not be reserved
system 00:00: iomem range 0xec000-0xeffff could not be reserved
system 00:00: iomem range 0xf0000-0xfffff could not be reserved
system 00:00: iomem range 0x100000-0xbfffffff could not be reserved
system 00:00: iomem range 0xfec00000-0xfed3ffff could not be reserved
system 00:00: iomem range 0xfed4c000-0xffffffff could not be reserved
system 00:02: ioport range 0x1000-0x107f has been reserved
system 00:02: ioport range 0x1180-0x11ff has been reserved
system 00:02: ioport range 0x800-0x80f has been reserved
system 00:02: ioport range 0x15e0-0x15ef has been reserved
system 00:02: ioport range 0x1600-0x167f has been reserved
system 00:02: ioport range 0x1680-0x169f has been reserved
system 00:02: iomem range 0xe0000000-0xefffffff has been reserved
system 00:02: iomem range 0xfed1c000-0xfed1ffff has been reserved
system 00:02: iomem range 0xfed10000-0xfed13fff has been reserved
system 00:02: iomem range 0xfed18000-0xfed18fff has been reserved
system 00:02: iomem range 0xfed19000-0xfed19fff has been reserved
system 00:02: iomem range 0xfed45000-0xfed4bfff has been reserved
pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1c.0:   IO window: disabled
pci 0000:00:1c.0:   MEM window: disabled
pci 0000:00:1c.0:   PREFETCH window: disabled
pci 0000:00:1c.1: PCI bridge, secondary bus 0000:03
pci 0000:00:1c.1:   IO window: disabled
pci 0000:00:1c.1:   MEM window: 0xf4300000-0xf43fffff
pci 0000:00:1c.1:   PREFETCH window: disabled
pci 0000:00:1c.2: PCI bridge, secondary bus 0000:04
pci 0000:00:1c.2:   IO window: 0x2000-0x2fff
pci 0000:00:1c.2:   MEM window: 0xfc000000-0xfc0fffff
pci 0000:00:1c.2:   PREFETCH window: 0xc0000000-0xc00fffff
pci 0000:00:1c.3: PCI bridge, secondary bus 0000:05
pci 0000:00:1c.3:   IO window: 0x3000-0x3fff
pci 0000:00:1c.3:   MEM window: 0xf8000000-0xf9ffffff
pci 0000:00:1c.3:   PREFETCH window: 0x000000f4000000-0x000000f40fffff
pci 0000:00:1c.4: PCI bridge, secondary bus 0000:0d
pci 0000:00:1c.4:   IO window: 0x4000-0x4fff
pci 0000:00:1c.4:   MEM window: 0xfa000000-0xfbffffff
pci 0000:00:1c.4:   PREFETCH window: 0x000000f4100000-0x000000f41fffff
pci 0000:15:00.0: CardBus bridge, secondary bus 0000:16
pci 0000:15:00.0:   IO window: 0x005000-0x0050ff
pci 0000:15:00.0:   IO window: 0x005400-0x0054ff
pci 0000:15:00.0:   PREFETCH window: 0xf0000000-0xf3ffffff
pci 0000:15:00.0:   MEM window: 0xc4000000-0xc7ffffff
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:15
pci 0000:00:1e.0:   IO window: 0x5000-0x8fff
pci 0000:00:1e.0:   MEM window: 0xf4800000-0xf7ffffff
pci 0000:00:1e.0:   PREFETCH window: 0x000000f0000000-0x000000f3ffffff
  alloc irq_desc for 20 on node 0
  alloc kstat_irqs on node 0
pci 0000:00:1c.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
pci 0000:00:1c.0: setting latency timer to 64
  alloc irq_desc for 21 on node 0
  alloc kstat_irqs on node 0
pci 0000:00:1c.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
pci 0000:00:1c.1: setting latency timer to 64
  alloc irq_desc for 22 on node 0
  alloc kstat_irqs on node 0
pci 0000:00:1c.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
pci 0000:00:1c.2: setting latency timer to 64
  alloc irq_desc for 23 on node 0
  alloc kstat_irqs on node 0
pci 0000:00:1c.3: PCI INT D -> GSI 23 (level, low) -> IRQ 23
pci 0000:00:1c.3: setting latency timer to 64
pci 0000:00:1c.4: PCI INT A -> GSI 20 (level, low) -> IRQ 20
pci 0000:00:1c.4: setting latency timer to 64
pci 0000:00:1e.0: setting latency timer to 64
  alloc irq_desc for 16 on node 0
  alloc kstat_irqs on node 0
pci 0000:15:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:03: resource 1 mem: [0xf4300000-0xf43fffff]
pci_bus 0000:04: resource 0 io:  [0x2000-0x2fff]
pci_bus 0000:04: resource 1 mem: [0xfc000000-0xfc0fffff]
pci_bus 0000:04: resource 2 pref mem [0xc0000000-0xc00fffff]
pci_bus 0000:05: resource 0 io:  [0x3000-0x3fff]
pci_bus 0000:05: resource 1 mem: [0xf8000000-0xf9ffffff]
pci_bus 0000:05: resource 2 pref mem [0xf4000000-0xf40fffff]
pci_bus 0000:0d: resource 0 io:  [0x4000-0x4fff]
pci_bus 0000:0d: resource 1 mem: [0xfa000000-0xfbffffff]
pci_bus 0000:0d: resource 2 pref mem [0xf4100000-0xf41fffff]
pci_bus 0000:15: resource 0 io:  [0x5000-0x8fff]
pci_bus 0000:15: resource 1 mem: [0xf4800000-0xf7ffffff]
pci_bus 0000:15: resource 2 pref mem [0xf0000000-0xf3ffffff]
pci_bus 0000:15: resource 3 io:  [0x00-0xffff]
pci_bus 0000:15: resource 4 mem: [0x000000-0xffffffffffffffff]
pci_bus 0000:16: resource 0 io:  [0x5000-0x50ff]
pci_bus 0000:16: resource 1 io:  [0x5400-0x54ff]
pci_bus 0000:16: resource 2 pref mem [0xf0000000-0xf3ffffff]
pci_bus 0000:16: resource 3 mem: [0xc4000000-0xc7ffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 524288 (order: 11, 8388608 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 524288 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
Freeing initrd memory: 12250k freed
Simple Boot Flag at 0x35 set to 0x1
audit: initializing netlink socket (disabled)
type=2000 audit(1265111316.653:1): initialized
HugeTLB registered 2 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
msgmni has been set to 7847
SELinux:  Registering netfilter hooks
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:02.0: Boot video device
  alloc irq_desc for 28 on node 0
  alloc kstat_irqs on node 0
pcieport-driver 0000:00:1c.0: irq 28 for MSI/MSI-X
pcieport-driver 0000:00:1c.0: setting latency timer to 64
  alloc irq_desc for 29 on node 0
  alloc kstat_irqs on node 0
pcieport-driver 0000:00:1c.1: irq 29 for MSI/MSI-X
pcieport-driver 0000:00:1c.1: setting latency timer to 64
  alloc irq_desc for 30 on node 0
  alloc kstat_irqs on node 0
pcieport-driver 0000:00:1c.2: irq 30 for MSI/MSI-X
pcieport-driver 0000:00:1c.2: setting latency timer to 64
  alloc irq_desc for 31 on node 0
  alloc kstat_irqs on node 0
pcieport-driver 0000:00:1c.3: irq 31 for MSI/MSI-X
pcieport-driver 0000:00:1c.3: setting latency timer to 64
  alloc irq_desc for 32 on node 0
  alloc kstat_irqs on node 0
pcieport-driver 0000:00:1c.4: irq 32 for MSI/MSI-X
pcieport-driver 0000:00:1c.4: setting latency timer to 64
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp 0000:00:1c.0:pcie04: HPC vendor_id 8086 device_id 2940 ss_vid 0 ss_did 0
pciehp 0000:00:1c.0:pcie04: service driver pciehp loaded
pciehp 0000:00:1c.1:pcie04: HPC vendor_id 8086 device_id 2942 ss_vid 0 ss_did 0
pciehp 0000:00:1c.1:pcie04: service driver pciehp loaded
pciehp 0000:00:1c.2:pcie04: HPC vendor_id 8086 device_id 2944 ss_vid 0 ss_did 0
pciehp 0000:00:1c.2:pcie04: service driver pciehp loaded
pciehp 0000:00:1c.3:pcie04: HPC vendor_id 8086 device_id 2946 ss_vid 0 ss_did 0
pciehp 0000:00:1c.3:pcie04: service driver pciehp loaded
pciehp 0000:00:1c.4:pcie04: HPC vendor_id 8086 device_id 2948 ss_vid 0 ss_did 0
pciehp 0000:00:1c.4:pcie04: service driver pciehp loaded
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
decode_hpp: Could not get hotplug parameters. Use defaults
acpiphp_glue: Slot 1 already registered by another hotplug driver
decode_hpp: Could not get hotplug parameters. Use defaults
acpiphp_glue: Slot 1 already registered by another hotplug driver
ACPI: AC Adapter [AC] (on-line)
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button [PWRF]
input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0C0D:00/input/input1
ACPI: Lid Switch [LID]
input: Sleep Button as /devices/LNXSYSTM:00/device:00/PNP0C0E:00/input/input2
ACPI: Sleep Button [SLPB]
ACPI: SSDT 00000000bd6d6c20 002C8 (v01  PmRef  Cpu0Ist 00003000 INTL 20050624)
ACPI: SSDT 00000000bd6d4020 0087A (v01  PmRef  Cpu0Cst 00003001 INTL 20050624)
Monitor-Mwait will be used to enter C-1 state
Monitor-Mwait will be used to enter C-2 state
Marking TSC unstable due to TSC halts in idle
ACPI: CPU0 (power states: C1[C1] C2[C2])
processor LNXCPU:00: registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: SSDT 00000000bd6d5ca0 001CF (v01  PmRef    ApIst 00003000 INTL 20050624)
ACPI: SSDT 00000000bd6d5f20 0008D (v01  PmRef    ApCst 00003000 INTL 20050624)
ACPI: CPU1 (power states: C1[C1] C2[C2])
processor LNXCPU:01: registered as cooling_device1
ACPI: Processor [CPU1] (supports 8 throttling states)
thermal LNXTHERM:01: registered as thermal_zone0
ACPI: Thermal Zone [THM0] (43 C)
thermal LNXTHERM:02: registered as thermal_zone1
ACPI: Thermal Zone [THM1] (42 C)
Non-volatile memory driver v1.3
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel Mobile Intel® GM45 Express Chipset
agpgart-intel 0000:00:00.0: detected 32764K stolen memory
ACPI: Battery Slot [BAT0] (battery present)
agpgart-intel 0000:00:00.0: AGP aperture is 256M @ 0xd0000000
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
brd: module loaded
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input3
ahci 0000:00:1f.2: version 3.0
ahci 0000:00:1f.2: PCI INT B -> GSI 16 (level, low) -> IRQ 16
  alloc irq_desc for 33 on node 0
  alloc kstat_irqs on node 0
ahci 0000:00:1f.2: irq 33 for MSI/MSI-X
ahci: SSS flag set, parallel bus scan disabled
ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 4 ports 3 Gbps 0x3 impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part 
ahci 0000:00:1f.2: setting latency timer to 64
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m2048@0xfc326000 port 0xfc326100 irq 33
ata2: SATA max UDMA/133 abar m2048@0xfc326000 port 0xfc326180 irq 33
ata3: DUMMY
ata4: DUMMY
Fixed MDIO Bus: probed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1a.7: power state changed by ACPI to D0
ehci_hcd 0000:00:1a.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1a.7: setting latency timer to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
ehci_hcd 0000:00:1a.7: cache line size of 64 is not supported
ehci_hcd 0000:00:1a.7: irq 23, io mem 0xfc326c00
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.31.12-174.2.3.fc12.x86_64 ehci_hcd
usb usb1: SerialNumber: 0000:00:1a.7
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ehci_hcd 0000:00:1d.7: power state changed by ACPI to D0
  alloc irq_desc for 19 on node 0
  alloc kstat_irqs on node 0
ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 19 (level, low) -> IRQ 19
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
ehci_hcd 0000:00:1d.7: irq 19, io mem 0xfc327000
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: EHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.31.12-174.2.3.fc12.x86_64 ehci_hcd
usb usb2: SerialNumber: 0000:00:1d.7
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1a.0: power state changed by ACPI to D0
uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
uhci_hcd 0000:00:1a.0: setting latency timer to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 20, io base 0x00001860
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.31.12-174.2.3.fc12.x86_64 uhci_hcd
usb usb3: SerialNumber: 0000:00:1a.0
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1a.1: setting latency timer to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 21, io base 0x00001880
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.31.12-174.2.3.fc12.x86_64 uhci_hcd
usb usb4: SerialNumber: 0000:00:1a.1
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
uhci_hcd 0000:00:1a.2: power state changed by ACPI to D0
uhci_hcd 0000:00:1a.2: PCI INT C -> GSI 22 (level, low) -> IRQ 22
uhci_hcd 0000:00:1a.2: setting latency timer to 64
uhci_hcd 0000:00:1a.2: UHCI Host Controller
uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1a.2: irq 22, io base 0x000018a0
usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb5: Product: UHCI Host Controller
usb usb5: Manufacturer: Linux 2.6.31.12-174.2.3.fc12.x86_64 uhci_hcd
usb usb5: SerialNumber: 0000:00:1a.2
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.0: power state changed by ACPI to D0
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.0: irq 16, io base 0x000018c0
usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb6: Product: UHCI Host Controller
usb usb6: Manufacturer: Linux 2.6.31.12-174.2.3.fc12.x86_64 uhci_hcd
usb usb6: SerialNumber: 0000:00:1d.0
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
  alloc irq_desc for 17 on node 0
  alloc kstat_irqs on node 0
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.1: irq 17, io base 0x000018e0
usb usb7: New USB device found, idVendor=1d6b, idProduct=0001
usb usb7: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb7: Product: UHCI Host Controller
usb usb7: Manufacturer: Linux 2.6.31.12-174.2.3.fc12.x86_64 uhci_hcd
usb usb7: SerialNumber: 0000:00:1d.1
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
  alloc irq_desc for 18 on node 0
  alloc kstat_irqs on node 0
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001c00
usb usb8: New USB device found, idVendor=1d6b, idProduct=0001
usb usb8: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb8: Product: UHCI Host Controller
usb usb8: Manufacturer: Linux 2.6.31.12-174.2.3.fc12.x86_64 uhci_hcd
usb usb8: SerialNumber: 0000:00:1d.2
usb usb8: configuration #1 chosen from 1 choice
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 2 ports detected
PNP: PS/2 Controller [PNP0303:KBD,PNP0f13:MOU] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
rtc_cmos 00:07: RTC can wake from S4
rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
PM: Resume from disk failed.
registered taskstats version 1
No TPM chip found, activating TPM-bypass!
  Magic number: 14:77:832
rtc_cmos 00:07: setting system clock to 2010-02-02 11:48:37 UTC (1265111317)
Initalizing network drop monitor service
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input4
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
ata1.00: HPA detected: current 625140335, native 625142448
ata1.00: ATA-8: WDC WD3200BEKT-00F3T0, 11.01A11, max UDMA/133
ata1.00: 625140335 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: ACPI cmd ef/02:00:00:00:00:a0 succeeded
ata1.00: ACPI cmd f5/00:00:00:00:00:a0 filtered out
ata1.00: ACPI cmd ef/10:03:00:00:00:a0 filtered out
ata1.00: configured for UDMA/133
ata1.00: configured for UDMA/133
ata1: EH complete
scsi 0:0:0:0: Direct-Access     ATA      WDC WD3200BEKT-0 11.0 PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 625140335 512-byte logical blocks: (320 GB/298 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 < sda5 sda6 sda7 >
sd 0:0:0:0: [sda] Attached SCSI disk
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 succeeded
ata2.00: ACPI cmd e3/00:02:00:00:00:a0 succeeded
ata2.00: ATAPI: MATSHITADVD-RAM UJ870A, SB04, max UDMA/33
ata2.00: ACPI cmd e3/00:1f:00:00:00:a0 succeeded
ata2.00: ACPI cmd e3/00:02:00:00:00:a0 succeeded
ata2.00: configured for UDMA/33
scsi 1:0:0:0: CD-ROM            MATSHITA DVD-RAM UJ870A   SB04 PQ: 0 ANSI: 5
usb 4-1: new full speed USB device using uhci_hcd and address 2
sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr 1:0:0:0: Attached scsi generic sg1 type 5
Freeing unused kernel memory: 1328k freed
Write protecting the kernel read-only data: 6356k
dracut: dracut-004-4.fc12
udev: starting version 145
Synaptics Touchpad, model: 1, fw: 7.0, id: 0x1c0b1, caps: 0xd04791/0xb00000
serio: Synaptics pass-through port at isa0060/serio1/input0
[drm] Initialized drm 1.1.0 20060810
i915 0000:00:02.0: power state changed by ACPI to D0
i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
i915 0000:00:02.0: setting latency timer to 64
input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input5
  alloc irq_desc for 34 on node 0
  alloc kstat_irqs on node 0
i915 0000:00:02.0: irq 34 for MSI/MSI-X
usb 4-1: New USB device found, idVendor=08ff, idProduct=2810
usb 4-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
usb 4-1: Product: Fingerprint Sensor
usb 4-1: configuration #1 chosen from 1 choice
[drm:intel_dp_i2c_init] *ERROR* i2c_init DPDDC-B
[drm:intel_dp_i2c_init] *ERROR* i2c_init DPDDC-C
[drm:intel_dp_i2c_init] *ERROR* i2c_init DPDDC-D
[drm] LVDS-8: set mode 1280x800 c
Console: switching to colour frame buffer device 160x50
fb0: inteldrmfb frame buffer device
registered panic notifier
acpi device:03: registered as cooling_device2
input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:02/input/input6
ACPI: Video Device [VID] (multi-head: yes  rom: no  post: no)
[drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
dracut: Starting plymouth daemon
firewire_ohci 0000:15:00.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
firewire_ohci: Added fw-ohci device 0000:15:00.1, OHCI version 1.10
yenta_cardbus 0000:15:00.0: CardBus bridge found [17aa:20c6]
device-mapper: multipath: version 1.1.0 loaded
yenta_cardbus 0000:15:00.0: ISA IRQ mask 0x0cb8, PCI irq 16
yenta_cardbus 0000:15:00.0: Socket status: 30000006
yenta_cardbus 0000:15:00.0: pcmcia: parent PCI bridge I/O window: 0x5000 - 0x8fff
yenta_cardbus 0000:15:00.0: pcmcia: parent PCI bridge Memory window: 0xf4800000 - 0xf7ffffff
yenta_cardbus 0000:15:00.0: pcmcia: parent PCI bridge Memory window: 0xf0000000 - 0xf3ffffff
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
dracut: Mounted root filesystem /dev/sda7
firewire_core: created device fw0: GUID 00016c2000bd1384, S400
dracut: Switching root
udev: starting version 145
i801_smbus 0000:00:1f.3: PCI INT A -> GSI 23 (level, low) -> IRQ 23
iTCO_vendor_support: vendor-support=0
ricoh-mmc: Ricoh MMC Controller disabling driver
ricoh-mmc: Copyright(c) Philip Langdale
ricoh-mmc: Ricoh MMC controller found at 0000:15:00.3 [1180:0843] (rev 11)
ricoh-mmc: Controller is now disabled.
e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k2
e1000e: Copyright (c) 1999-2008 Intel Corporation.
ACPI: WMI: Mapper loaded
e1000e 0000:00:19.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
e1000e 0000:00:19.0: pci_enable_pcie_error_reporting failed 0xfffffffb
e1000e 0000:00:19.0: setting latency timer to 64
  alloc irq_desc for 35 on node 0
  alloc kstat_irqs on node 0
e1000e 0000:00:19.0: irq 35 for MSI/MSI-X
thinkpad_acpi: ThinkPad ACPI Extras v0.23
thinkpad_acpi: http://ibm-acpi.sf.net/
thinkpad_acpi: ThinkPad BIOS 7UET71WW (3.01 ), EC 7VHT14WW-1.03
thinkpad_acpi: Lenovo ThinkPad R400, model 744311G
thinkpad_acpi: radio switch found; radios are enabled
thinkpad_acpi: This ThinkPad has standard ACPI backlight brightness control, supported by the ACPI video driver
thinkpad_acpi: Disabling thinkpad-acpi brightness events by default...
cfg80211: Calling CRDA to update world regulatory domain
Registered led device: tpacpi::thinklight
Registered led device: tpacpi::power
Registered led device: tpacpi::standby
Registered led device: tpacpi::thinkvantage
thinkpad_acpi: Standard ACPI backlight interface available, not loading native one.
input: ThinkPad Extra Buttons as /devices/virtual/input/input7
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pci 0000:15:00.2: SDHCI controller found [1180:0822] (rev 21)
sdhci-pci 0000:15:00.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
sdhci-pci 0000:15:00.2: Will use DMA mode even though HW doesn't fully claim to support it.
Registered led device: mmc0::
mmc0: SDHCI controller on PCI [0000:15:00.2] using DMA
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
iTCO_wdt: Found a ICH9M-E TCO device (Version=2, TCOBASE=0x1060)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
0000:00:19.0: eth0: (PCI Express:2.5GB/s:Width x1) 00:1c:25:a0:90:b7
0000:00:19.0: eth0: Intel(R) PRO/1000 Network Connection
0000:00:19.0: eth0: MAC: 7, PHY: 8, PBA No: 1008ff-0ff
iwlagn: Intel(R) Wireless WiFi Link AGN driver for Linux, 1.3.27kds
iwlagn: Copyright(c) 2003-2009 Intel Corporation
iwlagn 0000:03:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
iwlagn 0000:03:00.0: setting latency timer to 64
iwlagn 0000:03:00.0: Detected Intel Wireless WiFi Link 5100AGN REV=0x54
HDA Intel 0000:00:1b.0: PCI INT B -> GSI 17 (level, low) -> IRQ 17
HDA Intel 0000:00:1b.0: setting latency timer to 64
iwlagn 0000:03:00.0: Tunable channels: 13 802.11bg, 24 802.11a channels
  alloc irq_desc for 36 on node 0
  alloc kstat_irqs on node 0
iwlagn 0000:03:00.0: irq 36 for MSI/MSI-X
input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
input: HDA Intel Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input11
phy0: Selected rate control algorithm 'iwl-agn-rs'
cfg80211: World regulatory domain updated:
	(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
	(2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
	(2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
	(2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
	(5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
	(5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: Calling CRDA for country: CZ
cfg80211: Regulatory domain changed to country: CZ
	(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
	(2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm)
	(5150000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2301 mBm)
	(5250000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2301 mBm)
	(5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 3000 mBm)
usb 4-2: new full speed USB device using uhci_hcd and address 3
usb 4-2: New USB device found, idVendor=0a5c, idProduct=2145
usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 4-2: Product: ThinkPad Bluetooth with Enhanced Data Rate II
usb 4-2: Manufacturer: Lenovo Computer Corp
usb 4-2: configuration #1 chosen from 1 choice
Bluetooth: Core ver 2.15
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: Generic Bluetooth USB driver ver 0.6
usbcore: registered new interface driver btusb
IBM TrackPoint firmware: 0x0e, buttons: 3/3
input: TPPS/2 IBM TrackPoint as /devices/platform/i8042/serio1/serio2/input/input12
EXT3 FS on sda7, internal journal
fuse init (API version 7.12)
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Adding 4192924k swap on /dev/sda5.  Priority:-1 extents:1 across:4192924k 
microcode: CPU0 sig=0x6fd, pf=0x80, revision=0xa3
platform microcode: firmware: requesting intel-ucode/06-0f-0d
microcode: CPU1 sig=0x6fd, pf=0x80, revision=0xa3
platform microcode: firmware: requesting intel-ucode/06-0f-0d
Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
Microcode Update Driver: v2.00 removed.
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
vboxdrv: Trying to deactivate the NMI watchdog permanently...
vboxdrv: Successfully done.
vboxdrv: Found 2 processor cores.
VBoxDrv: dbg - g_abExecMemory=ffffffffa0381dc0
vboxdrv: fAsync=0 offMin=0x1b9 offMax=0x6ff
vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
vboxdrv: Successfully loaded version 3.1.2 (interface 0x00100001).
e1000e 0000:00:19.0: irq 35 for MSI/MSI-X
e1000e 0000:00:19.0: irq 35 for MSI/MSI-X
ADDRCONF(NETDEV_UP): eth0: link is not ready
iwlagn 0000:03:00.0: firmware: requesting iwlwifi-5000-2.ucode
iwlagn 0000:03:00.0: loaded firmware version 8.24.2.12
Registered led device: iwl-phy0::radio
Registered led device: iwl-phy0::assoc
Registered led device: iwl-phy0::RX
Registered led device: iwl-phy0::TX
ADDRCONF(NETDEV_UP): wlan0: link is not ready
Bluetooth: L2CAP ver 2.13
Bluetooth: L2CAP socket layer initialized
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bridge firewalling registered
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM ver 1.11
[drm:drm_mode_rmfb] *ERROR* tried to remove a fb that we didn't own
usb 4-2: USB disconnect, address 3
btusb_intr_complete: hci0 urb ffff880128817840 failed to resubmit (19)
btusb_bulk_complete: hci0 urb ffff8801288176c0 failed to resubmit (19)
btusb_bulk_complete: hci0 urb ffff880128817780 failed to resubmit (19)
btusb_send_frame: hci0 urb ffff8801288526c0 submission failed
CPU0 attaching NULL sched-domain.
CPU1 attaching NULL sched-domain.
CPU0 attaching sched-domain:
 domain 0: span 0-1 level MC
  groups: 0 1
CPU1 attaching sched-domain:
 domain 0: span 0-1 level MC
  groups: 1 0
wlan0: authenticate with AP 00:1e:8c:d3:8c:ac
wlan0: authenticated
wlan0: associate with AP 00:1e:8c:d3:8c:ac
wlan0: RX AssocResp from 00:1e:8c:d3:8c:ac (capab=0x411 status=0 aid=1)
wlan0: associated
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
Intel AES-NI instructions are not detected.
padlock: VIA PadLock not detected.
wlan0: no IPv6 routers present
CE: hpet increasing min_delta_ns to 15000 nsec
warning: `VirtualBox' uses 32-bit capabilities (legacy support in use)
vboxNetAdpOpen returns 0
device vboxnet0 entered promiscuous mode
vboxnet0: no IPv6 routers present
device vboxnet0 left promiscuous mode
npviewer.bin[8459]: segfault at ff999ed8 ip 00000000ff999ed8 sp 00000000ffb1de6c error 14
npviewer.bin[9157]: segfault at ff999ed8 ip 00000000ff999ed8 sp 00000000ffb58a1c error 14
npviewer.bin[9284]: segfault at ff999ed8 ip 00000000ff999ed8 sp 00000000ffc6e87c error 14

vsimam si tam nejakeho erroru s BlueTooth, a uplne na konci par segfaultu. bohuzel i kdybych se rozkrajel, nemam nejmensi zdani “co to je” a “proc to je” X-(

k udev teda take nejak nevim, na co se mam zamerit, co hledat a co sledovat. pri spousteni notebooku v USB nemam zadne zarizeni, ani ve firewire, nic… jen zapojena mechanika (SATA)…


# lsusb 
Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 08ff:2810 AuthenTec, Inc. 


# cat 60-fprint-autosuspend.rules 
SUBSYSTEM=="usb", ATTRS{idVendor}=="08ff", ATTRS{idProduct}=="5501", ATTR{power/level}="auto"
SUBSYSTEM=="usb", ATTRS{idVendor}=="08ff", ATTRS{idProduct}=="2500", ATTR{power/level}="auto"
SUBSYSTEM=="usb", ATTRS{idVendor}=="08ff", ATTRS{idProduct}=="2580", ATTR{power/level}="auto"
SUBSYSTEM=="usb", ATTRS{idVendor}=="045e", ATTRS{idProduct}=="00bb", ATTR{power/level}="auto"
SUBSYSTEM=="usb", ATTRS{idVendor}=="045e", ATTRS{idProduct}=="00bc", ATTR{power/level}="auto"
SUBSYSTEM=="usb", ATTRS{idVendor}=="045e", ATTRS{idProduct}=="00bd", ATTR{power/level}="auto"
SUBSYSTEM=="usb", ATTRS{idVendor}=="045e", ATTRS{idProduct}=="00ca", ATTR{power/level}="auto"
SUBSYSTEM=="usb", ATTRS{idVendor}=="05ba", ATTRS{idProduct}=="0007", ATTR{power/level}="auto"
SUBSYSTEM=="usb", ATTRS{idVendor}=="05ba", ATTRS{idProduct}=="0008", ATTR{power/level}="auto"
SUBSYSTEM=="usb", ATTRS{idVendor}=="05ba", ATTRS{idProduct}=="000a", ATTR{power/level}="auto"
SUBSYSTEM=="usb", ATTRS{idVendor}=="061a", ATTRS{idProduct}=="0110", ATTR{power/level}="auto"
SUBSYSTEM=="usb", ATTRS{idVendor}=="147e", ATTRS{idProduct}=="2016", ATTR{power/level}="auto"
SUBSYSTEM=="usb", ATTRS{idVendor}=="08ff", ATTRS{idProduct}=="1600", ATTR{power/level}="auto"
SUBSYSTEM=="usb", ATTRS{idVendor}=="08ff", ATTRS{idProduct}=="2810", ATTR{power/level}="auto"

snad jestli to nemuze byt zapla WiFi nebo vypnuty Bluetooth… WiFi mam zaplou permanentne a BlueTooth vypinam skriptem v rc.d pri kazdem bootu (protoze je ve vychozim nastaveni vzdy spustene).

PS: ty smajlici v tom code vypisu dmesg jsou vazne srandovni :slight_smile:

ten bluetooth vypinam v rc.local… mozna to neni uplne optimalni reseni


#
# turn off bluetooth
#
stat=`cat /proc/acpi/ibm/bluetooth | grep status | awk '{print $2}'`
if [ $stat = 'enabled' ]; then
  echo disable >/proc/acpi/ibm/bluetooth
fi
unset $stat

Prvni chyba: https://bugzilla.redhat.com/show_bug.cgi?id=538163

Muzes experimentovat s volbami jako intel_iommu=igfx_off pro kernel.

S tim usb nevim, na 4.1 je jen usb hub. Muze to ale souviset s prechozim, uvidime co na to Lenovo…:slight_smile:

tak sem si nastavil parametr pro kernel, chybovou hlasku to nevypise, ale i tak mi pred spustenim plymouthu vyskoci 3 radky nejakeho textu na tuze kratkou chvili (je i videt ve videu ktere sem poridil)… ale tak :slight_smile: snad uz to zadna bota neni

ad to USB, nasel sem bug: https://bugzilla.redhat.com/show_bug.cgi?id=505438 , ale zda se ze bez reseni

Tak to se situace moc nezmenila… vzhledem k tomu, ze oboji je to nefatalni tak bych to nechal byt, ono se to nejakyma aktualizacema spravi… snad. :slight_smile: